WHIRLPOOL BATHRINSTALLATION AND OPERATING MANUALJ-CORNER SHOWER TOWER™ENCLOSURE-Verona™
ILLUSTRATION 5ATTACHING MIXER VALVE TO SHOWER WALLSCREWQTY.-3NCROSS RECESSHEAD SCREW M4X12STAINLESS STEELEXTERNAL TOOTHLOCK-WASHER M4STAINLESS STEE
ILLUSTRATION 8OPINQTY.-3FLAT WASHER#8 TYPE BSTAINLESS STEELWASHERQTY.-3PPAN HEAD SCREW#8-32 x 1/2"STAINLESS STEELSCREWQTY.-3QSCREW QWASHER P
10TOWER INSTALLATION1. To locate the drilling template, place it over the bath. The template should be against the bath flange edgeand template corne
115. Attach Hot and Cold water supply lines of the mixer to the stub-out supply lines. (See Illustration 10.)6. Locate the on/off handle and temporari
12PLACING TOWERILLUSTRATION 117. Dry fit tower pins into holes to check hole location. Apply sealant around the three tower wall holes on thebath and
FIXED PANELBOTTOM RAILLAY A 1/4" BEAD OFSEALANT UNDER THEFIXED PANELTWOSCREWS15°ILLUSTRATION 14ILLUSTRATION 12ILLUSTRATION 13SR15°1/8"IMPORT
14FIXED PANEL ASSEMBLE TO BATH11. Screw 1 1/2" Allen set screw 3/4" deep into the bottom of the fixed panel. Lay a 1/4" bead of seala
ILLUSTRATION 19WASHER (1)SCREWS (2)SCREW INTOFIXED PANELYWXSCREW(1)SCREW HEREEXTERNAL TOOTHLOCK-WASHER #8STAINLESS STEELWASHERQTY.-1YBOLTQTY.-2WSHEET
ILLUSTRATION 20IMPORTANT:MUST DRILL AT A 15°ANGLE TO AVOIDDRILLING THROUGHROLLER TRACK OFTOP RING.ILLUSTRATION 22ABOLTQTY.-2WM3.5X9.5MMSTAINLESS STEEL
1716. Apply sealant in frame and extrusion. Align and place extrusion above end cap onto the fixed glass.FIXED GLASS FRAME END ATTACHMENTILLUSTRATION
17. Install on the sides of the tower the aluminum extrusions provided. They may be sealed in place or securedwith screws (S, quantity 6). Seal the
ILLUSTRATION 25FACEPLATETOWER WALLFOAMGASKETSEALANTHAND HELDSHOWERWASHERTOWER WALLFLEX HOSEWASHERTEFLONTAPEWATERCONNECTORWALL BARILLUSTRATION 27ILLUST
Printed in the U.S.A.PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.Jacuzzi Whirlpool
1ImportantThe bath must be installed according to installation instructions (F258000) for the Verona™ whirlpool bath.Follow the instructions to ensure
2FIXED PANELSEE PAGE 13 & 14BAILSSEE PAGE 6FACEPLATESEE PAGE 19WALLBARSEE PAGE 7MIXER (INCLUDINGHOSE CONNECTIONS)SEE PAGES 8 & 11L EXTRUSIONS
3EXPLODED VIEW OF J-CORNER SHOWER TOWEREND CAPSEE PAGE 18BOTTOM RAILSEE PAGE 13 & 14SET SCREWSEE PAGE 14
4Shower Tower HardwareIdentification ChartThe diagrams for these fasteners are shown actual size for fast identification.HARDWAREZLOW TRACKEND CAPCAPQ
5Shower Tower HardwareIdentification ChartThe diagrams for these fasteners are shown actual size for fast identification.HARDWARENUTQTY.-1JWASHERQTY.-
TOWER ASSEMBLY1. Assemble the four (4) bails to the tower wall.(See Illustration 1.) Do not overtighten thenuts on the threaded shaft end. Overtight
73. Attach the wallbar assembly to the tower wall.(See Illustration 3.)FLATHEAD SCREW#10-24 x 2 1/2"STAINLESS STEELHGILLUSTRATION 31/8" BEAD
Comments to this Manuals